Backup Light below License frame |
LED Backup Light |
Backup Light info - Amazon |
License Plate frame rakish angle - normal position |
Swings backward on impact |
Lucas-style backup light |
Backup light bracket |
Mount detail |
Final anti run-on installation lower fender - view from rear |
View from below |
Assembly ready to mount |
Mount before vacuum pipe added |
Carb drains |
Anti RunOn valve - proof-of-concept installation |
Valve as it comes from Moss |
Anti run-on as mounted - proof-of-concept installation |
Anti run-on plumbing |
Always hot relay powers timer on shutdown |
AntiRunonMolexCallouts.jpg |
AntiRunOnRelayAboveFootbox.jpg |
Delay timer |
Intermediate trafficator connector simplifies pulling stator tube wires |
Steadying the muffler - for tailpipe insertion or removal |
Driving tailpipe home - hammering on hose clamp |
Doug Reid remote clutch bleeder |
Replacement bleeder ready for installation |
Schematic view of remote clutch bleeder |
Bleeder connector detail |
DashSubDash3gauges.JPG |
Air Duct Adapter |
Tenax lifter tool |
Garmin installed with 1 ft cord |
USB charger with new dual-gauge panel |
KNairFuelCircuitBoard.JPG |
AirFuelmountedClose.JPG |
PoolNoodles.JPG |
Rear hub installer with bearing driver |
Rear hub installer - pvc pipe fittings |
Universal thread chaser |
WindowSealed.JPG |
Teflon2.JPG |
WindshieldTeflonTape1.JPG |
Socket extension as tap extension |
BoltsMetricSAE.JPG |
Facet mounted at 45 degrees with heat shield |
Mounting Facet at recommended 45 degree angle |
Facet45chassisSide1.JPG |
Facet45chassisEnd1.JPG |
Cap for hard brake pipe |
Wix on left Fram on Right |
GerowDrumInside.JPG |
GerowDrumOutside.JPG |
ThicknessGaugeAnnotated.jpg |
Healey gas tank dipstick |
Rebound removal.jpg |
Front axle dustcover slide hammer |
Front axle Dust Cover Installer |
SpeedoCounter.jpg |
FulcrumPinExtract.jpg |
RevisedCompressionExhMount.JPG |
Right side door check assy |
Door Opener friction spring |
Top Tensioner |
ParkBrakeBrace.JPG |
76reg0811LaCanada.JPG |
FuelTesterKit.jpg |
Stator wire pull setup |
Drill crimp connectors to remove |
Stator pull connection detail |
CapWithGasket.jpg |
GasketSeparated.jpg |
FillerNeck.JPG |
ClutchStudElongated0208.JPG |
ExhMountTop.jpg |
ExhMountBottom.jpg |
ShiftLeverPosition.JPG |
Gas gauge dampener |
ClutchMastPushrodWseal0308.JPG |
SealPinsPartialInsert.JPG |
sealPinsInstalled.JPG |
EngineRearCamAreaAvFormaGasket2.JPG |
CrankNutLockerSmall2.jpg |
LinkageBraceFront.JPG |
LinkageBraceSide.JPG |
3/16" x 2" homemade Allen socket |
Socket hanging from rear Allen screw |
healeydips111207.jpg |
Valve adjusting with Timing Disc |
Toe Gauge Left showing turnbuckle adjuster |
Toe Gauge Right |
Toe Gauge All |
toeCaliperDrawing0707.jpg |
Stant Cooling System Tester |
DormanCopperExpanPlugLgSpecsNum.jpg |
ExplansionPlugUglyBlock.JPG |
Brake Switch with Mount |
Brake Switch on Mount |
Mounted Brake Switch |
SwitchCloseUp.jpg |
SwitchOrderInfo.jpg |
Sender with Hylomar & Bonded Washers |
BondedWashers.JPG |